Edward 17
Edward
@Edward
published a new model October 29, 2023 at 12:52 PM
October 29, 2023 at 12:52 PM

Looks great, will give it a go on my next project, cheers.

Ctrl + Enter to send Enter to add a new line
Edward 17
Edward
@Edward
published a new model May 21, 2023 at 12:07 PM
May 21, 2023 at 12:07 PM

Ctrl + Enter to send Enter to add a new line
Edward 17
Edward
@Edward
published a new model April 24, 2023 at 10:22 AM
April 24, 2023 at 10:22 AM

Am I supposed to be able to screw it down tight? It took a bit of force to get the m5 socket head through the key hole, so maybe tightening isn't important? (edited)

@bnorick how your bolt goes into the key hole would depend on the diameter of its head. The general usage idea is that you can loosely screw in the bolt, insert it into the key hole freely then turn the assembly to tighten it in place (note the bolt head will eventually slip so you can't get as tight of a hold as with a screwdriver but you shouldn't need to). I did include the CAD files so feel free to modify it to M4 if that fits better for you.

Just had this printed on Treat Stock. Magnets are great. 10x3 fits perfectly. Also M5x8mm screw and nut also works great... but the "socket head cap" is too tall to fit any of my surge protectors. Gonna look into other thinner heads. Like a "countersunk socket cap".

Ctrl + Enter to send Enter to add a new line
Edward 17
Edward
@Edward
published a new model January 20, 2023 at 10:11 PM
January 20, 2023 at 10:11 PM

Is there any information on what the maximum thickness of a notebook it can hold?

Ctrl + Enter to send Enter to add a new line
Edward 17
Edward
@Edward
published a new model December 2, 2022 at 9:09 PM
December 2, 2022 at 9:09 PM

Ctrl + Enter to send Enter to add a new line
Edward 17
Edward
@Edward
published a new model October 8, 2022 at 12:42 AM
October 8, 2022 at 12:42 AM

I've found these to be super helpful with this full-rack I'm building out. Have printed a dozen to assist with wire-management.

Ctrl + Enter to send Enter to add a new line
Edward 17
Edward
@Edward
published a new model September 16, 2022 at 10:13 PM
September 16, 2022 at 10:13 PM

My husband and I printed this peg board for my quilting supplies- I love it because it sort of looks like a quilt itself.

Printed using Polymaker - White Marble PLA and PolyLite Rose silk PLA (which took a lot of tuning, we hadn’t used it before)

Ctrl + Enter to send Enter to add a new line
Edward 17
Edward
@Edward
published a new model September 14, 2022 at 2:26 PM
September 14, 2022 at 2:26 PM

Love the model and the fact that you've included the Fusion files! ❤ The arches you designed were too big to fit in the rail under my desk and I only had 10x2 magnets so I quickly made the changes and sent the file to my printer. A bit over hour later I have 10 of them attached under my desk. Magnets seem to be holding well with the press-fit.

I uploaded the remix, hopefully someone will find it handy: https://www.printables.com/model/910822-small-magnetic-cable-organizer (edited)

Adjusted to use 5mm diameter magnets. Works great.

@Edward couldn't have been easier. Had the magnets on hand already.

Thanks for sharing the files and saving me the trouble of making an inferior version of this, haha.

Ctrl + Enter to send Enter to add a new line
Edward 17
Edward
@Edward
published a new model August 29, 2022 at 9:37 PM
August 29, 2022 at 9:37 PM

Is there a chance someone can run this through CFD? :)

Ctrl + Enter to send Enter to add a new line
Edward 17
Edward
@Edward
published a new model July 6, 2022 at 10:53 AM
July 6, 2022 at 10:53 AM

Ctrl + Enter to send Enter to add a new line
All items loaded