a stl would be nice :)
@mrfrost_1239425 this is gcode generated directly by python code you can download it too, there is no 3D modeling or initial 3D object at any time. (edited)
@mrfrost_1239425 I have added an STL and some instructions on how to print it, let me know if it works for you.
View 2 more comments
@Protomodelos_543438 I have added an STL and some instructions on how to print it, let me know if it works for you
@function3d thank you very much! I'm in the middle of performing maintenance on my printer but as soon as it's done I'll try it out and will let you know how it works. I appreciate your help!
Ha sido complicado pero he conseguido hacerlo y que funcione. Estoy orgulloso.
It has been complicated but I did it. It is working. I am so proud.
I finally made one with some mods. The main is that I use old ATX power supply where I pick 5v and 12v from. This does not require 12-to-5v conversion module. 3.3v is taken from WeMos d1 module as in the original design. I also designed PCB for those components that were available for me. I can share a PCB layout if somebody needed. My system works with K-factors for PID-controller reset to zero, but I understand they potentially not optimal and I still need to tune the up. Great project. Many thanks...
View one more comment
Uni baxam koʻrasizmi
@Gonzaltant can you make a guide to build this with the atx power supply? i have an old one.
.16mm layer height / 2mm raft @ 75% fill / 50% print speed / Sunlu PLA+
Printed amazing, no issues at all! Was very easy to pull off the raft (I figured I would need one to help with adhesion and prevent curling). Very fun, such a good fidget toy, and my cats love it too!
Funciona perfecto. Si se afila bien corta hasta papel.
It works perfect. If it is well sharped it can cut even paper.
@Nixeris_1787062 Gracias por el dato
it works, but with P1P the coverplate of headtool hit the border it's possible center the tree? how can modify a so long Gcode?
I have a Kobra 2 Max, can you show a pic how the filament would feed to the sensor/bowden on the side? Worried about that angle. Thanks!
@Darthkat_517192 Sorry for the late reply, there is no way to do that, I don't use the bowden or the filament sensor, this support is designed for the filament to load vertically in the extruder, I use a ~8cm bowden tube and put a small piece of filament in the sensor to be always active
I made a remix of these backstops so they would work in concert with this lid riser ( https://www.printables.com/model/612282-riser-upgrade-for-kingroon-klp1). Thank you for providing this model. Two thumbs up.
Hi, is there a way to get an editable file for the shorter screw piece ? I'd like to make a remix as I'd need to mount it to the side of my enclosure with some screws
@Angelo_843822 I have updated with the STEP file, I hope it works for you.
Nice pattern. Sliced it a little differently by adding a negative volume box to the Tissue Box - Box.stl since I had to cut the model in two to fit it on my Mini+. Also resized the lid and printed it at 100% infill so that it will press down onto the soft packaging of the tissues that I use and get progressively lower as the tissues are used up; hopefully no more need to reach into the packaging to restart the tissue dispensing.
Printed with Prusament Mystic Green PLA on a P-Flat sheet.
Made one exactly according to the design shared. Then a smaller one to fit standard 20cm diameter spools.
Do you have any experience with inner spool radius that avoids breaking PET joints? I'll try with this smaller spool (internal diameter 16cm) and see :)
