Capybara Phone Holder / Keyring

Easy to print low-poly model of Capybara made to hold the smartphone + Normal (no hole for phone) and Keyring models
En el concurso Low Poly
1693
5939
143
19 k
actualizado 28 de julio de 2024

Descripción

PDF

Capybara
Version v1.2 - 14 IV 2024

There is a front (head in front of the screen) and reversed (head behind phone) model and a full model without a hole for a phone

Additionally there are keyring addons (to front or back) that you can use with a desired Capybara model

In files there is also V11.zip file with older version of capybara if you like it more
More about changes on the bottom in Updates section

---

If you want to sell prints of this models you can buy a Commercial License here:
https://cults3d.com/en/3d-model/gadget/capybara-phone-holder-keyring-commercial-license

Check Phone Collection for more models
https://www.printables.com/@C47_3d/collections/793008

---

Printing Timelapse of 3 capybaras
https://www.instagram.com/p/Cv1zEdfNVQ-

---

Number in file names is a space for a phone in mm
For phone thickness of 6-16mm - they are also on the bottom of models to show what size it is after print

To resize the models use the equasion:
'Needed space (in milimeters)' divided by 'model number' multiplied by 100% = 'Needed model size in percent'
For example if you need more stable 16mm you can take 10mm version resized to: 16 / 10 * 100% = 160%

May not be suitable for phone set vertically but it depends on phone size and its weight
The smaller the gap between the print and a phone the better chance it will not fall
Reversed version may be better for this
You can also resize smaller version to the bigger size
Version 1.2 is longer so it should be more stable than older models

The gap is cut with 16dgr angle
 

---

To make a keyring use a Capybara model of your choice and add there a keyring model (back or front). Version for back can be moved to different place and rotated (for example if you want it on side of capybara)
Then merge both models - see a screen from Cura and PrusaSlicer on the last photo
Keyring models are with a 'frame', a flat surface that will not be printed. This way it is easy to set it in the right spot with a Capybara - Ignore model 'errors' and DO NOT try to 'fix' the model

Solid version of Capybara (without a hole for a phone) is with a sepparate files that are already with a keyring
CapybaraV12-keyring
CapybaraV12-keyring_HOLES

CapybaraV12-long is a longer version, the same as used for phones
Use a CapybaraV12_keyring-addon_back file with it

---

HOLES version
For a filament string used as eyes - usually a black one
Push it in with a pliers, then cut it with cutting pliers or a knife (be carefull to not damage the print or yourself)
Then you can use some a heatgun, small torch or a lighter to smooth the cutted end

---

Update 16 VIII 2023
Small change to sides and back of the model. Will be easier to print and use with a kechain
Added keychain models

Update 29 VIII 2023
Changed from versions 12-16mm to 10-15mm with more precise angles
You can resize the model for different phone thickness
Angle changed from ~16,5dgr to 16dgr

Update 31 VIII 2023
Changed Keyring-back addon. Looks and works better
Added photos of a new keyring print

UPDATE 06 I 2024
Added versions for 6-9mm phones

UPDATE 05 IV 2024
Added numbers on the bottom of models to show what size it is after print
Added 'mm' to file names to avoid rare confusions
Added version for 16mm phone
Changed keyring addons a little (should be stronger)
Changed 'C47_3D' on the bottom for easier printing

UPDATE 14 IV 2024 - V1.2
Reshaped some details of a Capybara for a nicer print (better angles so there will be less stair-like layers ). Also the model is little cleaner, especially in the bottom
PHONE versions are longer and with a hole that starts from a lower position - this way it is more stable and can be used with a phone set vertically with much more smartphone models
Reversed version holes now starts from the same position on the back - so now no matter what size version you will print it will look the same with a smartphone
Added HOLES version to use a filemant string as eyes
Keyring_back is longer - so more space for a ring and even more stability
Keyring_front is changed and moved more to front for more space for a ring

---

Print Settings

Printed with 0.4mm nozzle
NO supports needed
0.1mm layer height (you can use 0.2mm too)
2 walls
7% gyroic infill (I used no infill with Prusa Slicer that automaticly adds some inner bridges when needed)

---

Etiquetas



Premiado en el concurso


Low Poly
470 modelos | 11 de agosto – 20 de agosto de 2023

Origen del modelo

El autor ha marcado este modelo como su creación original.

Licencia


Modelos destacados del creador

Ver más